how to change screen on iphone 6

Introduction

Learn how to replace your iPhone 6 screen. This part comes with the front-facing camera, earpiece speaker and LCD shield plate already installed, making for an easier repair.

All y'all need to do is remove the old screen and transfer the abode push button to the new screen.

You can also use this guide to replace the front panel assembly cablevision bracket.

Video Overview

• Earlier disassembling your iPhone, discharge the battery beneath 25%. A charged lithium-ion battery can catch burn and/or explode if accidentally punctured.

• Ability off your iPhone before offset disassembly.

• Remove the ii three.6 mm-long P2 Pentalobe screws next to the Lightning connector.



• If your display glass is cracked, keep farther breakage contained and forestall bodily harm during your repair by taping over the glass.

• Lay overlapping strips of clear packing tape over the iPhone'southward display until the whole face is covered.

• This will keep glass shards contained and provide structural integrity when prying and lifting the display.

• Wear safety spectacles to protect your optics from any glass shaken costless during the repair.

• If the broken glass makes it difficult to get a suction cup to stick in the next few steps, attempt folding a strong piece of tape (such as duct tape) into a handle and lifting the brandish with that instead.

• The next three steps demonstrate using the iSclack, a cracking tool for safely opening the iPhone half-dozen that we recommend for anyone doing more than one repair. If you aren't using the iSclack, skip down three steps for an alternating method.

• If the plastic depth judge is fastened at the center of the iSclack, remove it now—information technology'south not needed for larger phones similar the iPhone 6.

• Shut the handle on the iSclack, opening the suction-cup jaws.

• Place the bottom of your iPhone in between the suction cups.

• Position the iSclack's upper suction loving cup against the display, just to a higher place (but non covering) the home button.

• Open the handles to shut the jaws of the iSclack. Center the suction cups and press them firmly onto the meridian and bottom of the iPhone.

• If your brandish or back glass is badly cracked, roofing it with a layer of clear packing tape may help the suction cups attach. The iSclack too includes 2 pieces of tape for this purpose.

• Hold onto your iPhone deeply and close the handle of the iSclack to split the suction cups, pulling the front panel up from the rear case.

• The iSclack is designed to safely open your iPhone just enough to split up the pieces, merely not enough to damage the display cables.

• Skin the two suction cups off your iPhone.

• Skip the next three steps and continue on to Pace viii.

• If you don't accept an iSclack, utilize a unmarried suction cup to elevator the front panel:

• Printing a suction cup onto the screen, just to a higher place the home push.

• Be sure the cup is pressed securely onto the screen to become a tight seal.

• If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction loving cup to adhere. Alternatively, very stiff tape may be used instead of the suction loving cup. If all else fails, you can superglue the suction cup to the broken screen.

• While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the front panel assembly from the rear case.

• Accept your time and utilize firm, constant force. The display associates is a much tighter fit than most devices.

• Using a plastic opening tool, begin to gently pry the rear case downwardly, away from the brandish associates, while standing to pull up with the suction loving cup.

• There are several clips holding the forepart panel assembly to the rear case, so you may demand to use a combination of the suction cup and plastic opening tool to free the forepart panel assembly.

• Pull the plastic nub to release the vacuum seal on the suction cup.

• Remove the suction cup from the display assembly.

• Open the iPhone past swinging the home button end of the front panel associates away from the rear case, using the top of the phone every bit a hinge.

• Several clips along the top border of the front console form a partial hinge.

• During reassembly, align the clips just below the top edge of the rear example. And then, slide the front panel upwardly until its tiptop edge is flush with that of the rear case.

• Open up the display to about a 90º angle, and lean it against something to continue it propped up while yous're working on the phone.

• In a pinch, an unopened canned potable works well for this.

• Add a rubber band to keep the display securely in place while y'all work. This prevents undue strain on the display cables.

• Remove the following Phillips screws from the bombardment connector bracket:

• I 2.2 mm screw

• One iii.2 mm screw

• During your repair, keep track of each screw and make certain it goes back exactly where it came from to avoid damaging your phone.

• Remove the metal bombardment connector bracket from the iPhone.

• Use a plastic opening tool to gently pry the battery connector up from its socket on the logic board.

• Take care to only pry upward on the battery connector, and not the socket on the logic board. If you pry upwards on the logic lath socket, you may break the connector entirely.

• Remove the following v Phillips screws securing the front panel associates cable bracket:

• Three one.2 mm screws

• Ane i.7 mm screw

• Ane 3.i mm screw

• Incorrect placement of these screws during reassembly will cause permanent damage to your iPhone's logic board.

• Remove the forepart console associates cable subclass from the logic board.

• In the next 4 steps, take care to pry upwards simply on the cable connectors, and not on their sockets on the logic lath.

• Use a spudger or a fingernail to disconnect the front end-facing camera and sensor cablevision connector.

• Employ a spudger or a fingernail to disconnect the home button cablevision connector.

• Make sure the battery is asunder before you lot disconnect or reconnect the cable in this step.

• Use a spudger or a fingernail to disconnect the display data cable connector.

• When reassembling your phone, the brandish information cablevision may pop off its connector. This can result in white lines or a blank screen when powering your phone back on. If that happens, only reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery connector.

• Use the flat end of a spudger to disconnect the digitizer cable connector.

• When reconnecting the digitizer cable, practice not press the center of the connector. Printing one finish of the connector, and then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer harm.

• Remove the forepart panel associates from the rear example.

• Remove the two 1.9 mm Phillips screws securing the home push button bracket.

• Remove the dwelling button bracket from the front end console.

• Use the indicate of a spudger to disconnect the home button cable connector by pushing it up and abroad from the home push button.

• The rubber membrane surrounding the home button is very sparse and tears easily.

• Utilize mild oestrus (with an iOpener, heat gun, or pilus dryer) to soften the agglutinative securing the habitation button membrane.

• Using your fingertip, utilise business firm, abiding pressure on the home button from the front side of the display assembly, until the membrane starts to divide from the forepart panel.

• Practice non push the domicile button all the manner through—you but need to get a corner free and so that you can pry it free with a spudger.

• Pare the habitation button the residual of the way off of the display by prying gently with a spudger.

• Use the point of a spudger to carefully separate the home button cablevision from the adhesive securing it to the front panel.

• If the cable doesn't separate easily, apply oestrus using an iOpener or hair dryer to soften the adhesive, and endeavor again. Exist careful not to damage the cable.

• One time all the agglutinative has been separated, remove the habitation push from the front console.

• If you are replacing a cleaved forepart panel, there may exist drinking glass shards stuck to the habitation button. Carefully remove any remaining glass earlier transferring your habitation button to a new display.

• Your replacement part may come with an extra Phillips screw already installed left of the Abode Button. Remove the unnecessary screw so that you tin reinstall the home button bracket.

Conclusion

To reassemble your device, follow these instructions in reverse club.

Embed this guide

Choose a size and copy the code below to embed this guide equally a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/iPhone+6+Screen+Replacement/29339

Posted by: negronwentiont.blogspot.com

Share this post