How To Change A Headlight In A 2016 Chevrolet Sonic

Chevrolet Sonic Headlight Bulbs Replacement Guide
How to change the low beam, high beam & front plow indicate light bulbs in the headlights of a 2012-2014 GM Chevy Sonic.

2013 Sonic Headlight
Turn Bespeak, Low Beam, High Beam
Low Beam Headlight This automotive maintenance tutorial was specifically written to assist owners of the first generation (2012, 2013, 2014, 2015 & 2016) Chevy Sonic in irresolute a burnt out low beam, high beam and front turn indicate light bulb in the headlight assemblies.

Owners of other Full general Motors vehicles such equally the Spark, Cruze, Malibu, Impala, Traverse, Tahoe, GMC Terrain, Acadia, Yukon, Buick Verano, Regal, LaCrosse, Encore, Enclave and Holden Barina may likewise find these DIY instructions to be helpful.

Replacement headlight bulbs with their part numbers are every bit follows: Low Beam # H11, Loftier Axle # 9005 and Forepart Turn Signal # 7444NA.

No tools are required to alter whatsoever of the bulbs in either the commuter or passenger side headlight housings.

A minor flathead screwdriver may be useful for prying off the power plugs.

Low Beam Dust Cap
Twist Off Low Beam Cover
Base of Low Axle Bulb The low beam seedling is located at the center of the headlight assembly.

Accomplish in behind the headlight and locate the round black plastic dust cap covering the depression beam bulb.

Rotate the cap one/4 turn counter clockwise and remove it. Set it aside in a safe identify.

Pry Off Power Plug
Plug Disconnected
1/4 Turn Counter Clockwise Pull back the retaining clip on the electric connector and slide information technology direct off the base of operations of the sometime depression beam bulb.

You may need to pry up the clip using a small-scale flathead screwdriver.

Rotate the base of the old bulb 1/4 turn counter clockwise and pull information technology straight out of the headlight housing.

Remove Low Beam Bulb
Osram # H11 12V 55W
Insert New Low Beam Try to avoid touching the drinking glass part of the new bulb with your fingers or anything greasy in the engine bay.

If y'all do get the bulb dirty, wipe information technology clean with an alcohol moistened paper towel.

i/4 Plow Clockwise - Lock
Push On Ability Plug
Cap - 1/4 Turn Clockwise Insert the new # H11 low beam bulb in to the socket and rotate it i/4 plow clockwise to lock it in identify.

Push button the power plug straight on to the base of operations of the new bulb until it clicks deeply in to identify.

Replace the blackness plastic grit cover and rotate information technology 1/4 turn clockwise.

Loftier Beam - Inner Corner
Loftier Axle Dust Cap
1/four Turn Counter Clockwise The high beam bulb is located at the inner corner of the headlight assembly.

Reach in backside the headlight housing and twist the circular black plastic dust cap 1/iv plough counter clockwise to remove it.

Set the dust cover aside in a condom identify.

Base of operations of High Beam Bulb
Pry Off Electrical Connector
i/4 Turn Counter Clockwise Gently pull back on the electric connector'south retaining clip and pull the plug straight off the base of operations of the old high beam bulb.

If you accept problem removing the power plug, use a small flathead screwdriver to pry off the clip.

Rotate the base of operations of the onetime bulb 1/4 turn counter clockwise and pull it straight out of the housing.

Remove High Axle Seedling
Sylvania 9005 12V 60W
Insert New # 9005 Bulb Try to avert touching the glass office of the new seedling with your fingers or anything greasy in the engine bay.

If y'all practise go the bulb muddy, wipe it clean with an alcohol moistened paper towel.

1/4 Plow Clockwise - Lock
Twist On High Beam Cover
Plow Indicate / Side Marking Insert the new # 9005 loftier beam bulb in to the socket and rotate information technology one/4 turn clockwise to secure it in identify.

Twist on the plastic dust cap one/4 turn clockwise.

Socket At Outer Corner
1/4 Plough Counter Clockwise
Pull Out Turn Point Socket The front turn signal bulb is located at the outer corner of the headlight assembly.

Reach in and rotate the socket ane/4 turn clockwise before pulling it straight out of the housing.

Pull Out Onetime # 7444NA
Test New Headlight Bulbs
Testing High Beam Pull the old bulb straight out of the socket and button in a new amber colored # 7444NA bulb.

Re-insert the socket in to the housing and rotate it 1/iv plough clockwise to lock information technology in place.

Test the new bulbs by turning on the headlights, activating the hazard signals and flashing the high beams.

For more, check out my other Chevy Sonic Repair & Maintenance Guides.

Source: https://www.paulstravelpictures.com/GM-Chevrolet-Sonic-Headlight-Bulbs-Replacement-Guide/

Posted by: negronwentiont.blogspot.com

Share this post